Mapesil T Plus How To Use
With first-class water and abrasion resistance, Mapei's Ultracolour Plus with its wide range of colours, offers the perfect grouted terminate to the tile installation.
Materials required:
- Mapei Ultracolour Plus
- 500ml H2o
- Mapesil AC Silicone
Tools & accessories required:
- Floor protection canvass
- Mixing bucket
- Protective gloves
- Mechanical stirrer
- Soft condom float
- 2x Buckets of h2o
- 2x Sponges
- Microfibre cloth
- Silicone applicator gun
Shop ALL TILING TOOLS & ACCESSORIES HERE
Preparing and applying Ultracolour plus grout
Preparing the area
Before considering grouting, ideally all spacers should exist removed. Ensure that all joints are gratuitous from adhesive or any loose material. When applying grout to the walls, ensure that all areas are protected from spillage. The key to applying grout to an excellent finish is not only in the application, but in the mixing itself.
Mixing the grout
When mixing Mapei Ultracolour Plus the bag must be shaken to ensure an fifty-fifty distribution of ingredients. A clean mixing vessel should be used and the minimum recommended water placed in the bucket. Measuring water on site can be difficult so an empty 500ml drinks canteen tin exist used to measure the h2o.
When 0.9l of water is in the bucket, the pocketbook can be opened and all the contents poured into the saucepan. The mixing of the product should exist carried out by mechanical means. During the mixing the product will appear dry but this is expected.
Afterward mixing with the paddle for approximately 2 minutes, the product should be allowed to stand for 2-3 minutes, this will allow the production to slake. After ii-3 minutes the product can be remixed. If at this point the product still appears too dry out, the remaining 0.1l of water may be added.
Once mixed, the grout will remain workable for approximately 20-25 minutes. If the grout begins to harden in the bucket, it can be remixed with the mechanical stirrer, but exercise non add any more h2o.
Applying Grout to the Wall
The grout can then exist practical to the wall surface using a soft, rubber float. The method of application is down to personal preference, still pointing the joints in a way that allows the air to be removed from the joint is advisable.
The grout must exist compacted into the joint, ensuring a full articulation is achieved. A simple spread over the superlative surface could lead to the materials sitting at the surface of the joint, either leaving a void behind or assuasive pinholing to occur during the washing off procedure.
In one case the grout is in the joint, the grout float can be used at a 45 degree angle to remove excess from the tile surface. Intendance should exist taken at this point and then as not to remove besides much of the grout from the joint itself.
In one case the grout has been applied and the textile on the surface begins to dry out, the washing off procedure can brainstorm.
Washing off backlog grout
It is appropriate to have two clean buckets of h2o at this point. The offset bucket volition exist used to rinse the sponge of the bulk textile. The second will be used every bit a secondary clean.
Soak the sponge in clean h2o and wring out until merely clammy. In the starting time example, we are simply looking to remove the grout from the surface of the tiles. A round motion tin can exist adopted for this.
Regular rinsing of the sponge will prevent the excess grout simply being moved around the surface of the tiling. When the backlog grout has been removed, the secondary wash can take place. A diagonal motility turning the sponge regularly will remove the remaining film.
Preparing internal corners for sealant and creating a perfect articulation end
The internal corner and movement joints must be free from any grout material and tin can exist cleaned out at this stage.
If any pinholes or low spots have occurred, simply summit these areas up with the grout cloth and sponge off. After this step has been completed, nosotros tin can concentrate on the joint finish. With the sponge, strike the joints to ensure an even terminate to the surface.
Please ensure that the sponge is only damp throughout all of the aforementioned process, as backlog h2o applied at whatsoever phase can have a detrimental effect on the grout finish.
Removing excess movie
Although several washes take been carried out, a slight flick may be left on the surface of the tile. This can exist removed after a couple of hours with a microfibre cloth. Just buff the surface of the tiles removing the rest.
Applying Mapesil AC
Once the Mapei Ultracolour Plus has dried, Mapesil AC should exist used in all areas subject area to motion, such as internal corners and effectually baths and showers.
To install the Mapesil AC, cut the summit of the tube. The nozzle tin then be screwed onto the silicone tube. The small-scale terminate of the nozzle must be cut at a 45 caste angle to a slightly wider opening than the joint width.
In one case cut, the tube tin be loaded into a suitable silicone applicator gun. The nozzle can be offered to the joint, to cheque that the nozzle cut width is slightly larger than the joint width. Squeezing the trigger will push the new silicone into the nozzle and this can exist wiped at the cease.
The silicone can then be applied to the corner. A slow, steady pace should be adopted, squeezing the trigger consistently. Once the articulation has been covered, nosotros are gear up to finish the joints. For ease, water can be used - wet the finger and shine gently over the joint, wiping whatever excess silicone away.
Share your photos with us on Twitter or Instagram to exist featured, using #TileGiant
Head over to our YouTube channel to browse more how-to videos, or contact our team for further proficient advice.
Source: https://www.tilegiant.co.uk/news/how-to-mix-and-apply-ultracolour-plus-and-mapesil/
0 Response to "Mapesil T Plus How To Use"
Post a Comment